Rakentelu Foorumi

Qrolle, Elecraft, Atmel, Pic, LC-Meter, OBD2, Robotit, yms yms
Tänään on To Maalis 28, 2024 3:37 pm

Kaikki ajat ovat UTC + 2 tuntia




Aloita uusi ketju Vastaa viestiin  [ 12 viestiä ] 
Kirjoittaja Viesti
 Viestin otsikko: Parasitic on 40m band
ViestiLähetetty: Pe Huhti 14, 2006 9:14 pm 
Poissa
Avatar

Liittynyt: La Huhti 02, 2005 11:45 pm
Viestit: 97
Paikkakunta: Seinäjoki
Tulin tänne mökille tornioon, vetäisin windomin puihin.
muut bandit on ok, mutta 40m:llä kun teho potikkaa kääntää niin että juuri 10w ylittyy (100w pääte just käynnistyy) niin tehot ryntää 150w hujakoille ja rigi ottaa virtaa abt. 25A. alle 10w teholla ihan ok. Ei swrriä ja muilla bandeilla teho toimii, mutta tää 40m temppuilee.

Voiko tuo johtua RF-ongelmasta? Tiedän että tuo windomi ei ole antenni, mutta täällä ei oikein saa montaa dipolia vedettyä ja silti pitäis monelle bandille päästä...

Ja lisäksi ilmeisesti tuo avestapolaris joka on muutaman kilsan päässä antaa 80m:lle kovat pörinät.. ei taida tulla kalakukosta mitään...


EDIT: Muutin otsikon

_________________
Elecraft K2 #5272


Viimeksi muokannut oh6kw päivämäärä Ma Elo 14, 2006 3:30 pm, muokattu yhteensä 1 kerran

Ylös
 Profiili  
 
 Viestin otsikko:
ViestiLähetetty: La Huhti 15, 2006 12:34 pm 
Poissa

Liittynyt: Ke Tammi 25, 2006 10:59 am
Viestit: 210
Paikkakunta: Pieksämäki
Valitettava ongelma. Koitin etsiä vastaavaa tuolta postilistalta. Ei ihan samaa löytynyt. Kun rigi toimii qrp:na ja muilla bandeilla normaalisti isollakin teholla voi kyllä olla RF-peräinen ongelma. ALC ongelman ollessa kyseessä pitäisi olla sama vika joka bandilla. Kannattaa laittaa kyselyä elecraftille tai tonne listan asiantuntijoille.

73 Jukka


Ylös
 Profiili  
 
 Viestin otsikko:
ViestiLähetetty: La Huhti 15, 2006 12:48 pm 
Poissa
Avatar

Liittynyt: La Huhti 02, 2005 11:45 pm
Viestit: 97
Paikkakunta: Seinäjoki
vika selvis...
Mulla oli yksi ylimääräinen kapistus radiossa kiinni, mitä en yleensä siinä käytä.. Nimittäin mikrofoni. Sen kun nyppäs irti niin ongelman hävis eli RF meni ilmeisesti mikrofonin kautta sisään.

Ja varmaan tuo windomi teki osansa... kunnon dipolilla ei välttämättä olis ollu ongelmia.

Mutta hatun nosto taas elecraftille. Laitoin illalla vielä sinne kysymyksen olisko niillä antaa vinkkiä ja vastaus tuli tosi nopsaan.

Lainaa:
Hi Jarno,

It could be due to RF getting into the rig, since the 40m band has the most
power gain and if problems are going to happen, that is usually the band on
which they will occur. It might help to try an antenna tuner too, either a
manual tuner or one of the automatic tuners we make such as the KAT100 150w
auto tuner.

But first be sure all of the shield grounding measures are in place
correctly, including the 2 solder lugs between the KPA100 PA shield and one
screw of the SO-230 antenna connector. The 3 spring clips should also be in
place, and making good contact with the insides of the K2 side panels and
KPA100 rear panel. Be sure to remove all paint in the area where the clips
make contact. See the attached template for where to remove the paint.

Also ground the mic connector. I do this by removing the left side panel and
scraping away enough green solder mask right next to the threaded part of
the connector so that I can solder it directly to the PCB ground plane. If
you remove the PCB coating about 1/4 of the way around the threaded portion
of the mic shell, it’s enough to allow a good soldered connection. A tiny
jewelers screwdriver works well for removing the resist. Use the side of a
soldering iron tip and enough heat to get the shell hot enough to take
solder and then apply solder between the PCB and the bottom edge of the
connector shell. Cool the threaded mic connector with a damp rag or sponge
when done, so you don't burn yourself on the hot connector.

Be sure all chassis screws are tight, and all of the green, paint masking
tape was removed where the threaded 2-D fasteners connect the panels. The
mounting screws on Q1, Q2 of the KPA100 PA transistors will loosen after the
first few minutes of operation, and they will need to be retightened.

Do not leave the internal frequency counter probe installed in TP2, as it
can pick up RF and cause problems. It can also be damaged when the KPA100 is
installed due to close clearance between the K2 and the KPA100.

In some difficult cases, you may find it necessary to adjust the length of
the feedline, antenna, or the station ground to change the impedance and SWR
seen by the rig. Changing the feedline by 1, 2, or 5 feet sometimes will
move a hard to match or high RF current or voltage away from the rig. It’s
usually pretty easy to add in or remove a short section of feedline, so that
is one the first things to try after the things mentioned above. Coils of
the feedline or ferrite beads on the DC and RF cables may also be helpful in
some cases.

In some cases where a good RF ground is not possible, such as on poor soil
or a 2nd or 3rd story building, you may need to use an electrical 1/4
wavelength ground counterpoise wire, or an artificial ground tuner like
those made by MFJ. You can use more than 1 counterpoise to operate over
several bands, with each one cut to the proper electrical 1/4 wavelength, if
it is necessary.

If the antenna is close to the rig, or if there is a lot of RF in the shack,
you may need to change the grounding, use a 1/4 wave counterpoise, tuner, or
relocate the antenna. Sometimes just moving the rig around and how it is
connected will calm things down.

Some linear-mode (not switching mode) Astron power supplies have been know
to cause problems when RF gets into their regulator circuit. Try another
power supply if this is suspected, if possible.

Try removing the mic, headphones, or paddles to see if RF is getting into
the rig from that path. Then transmit with the TUNE button and see if the
power control is more stable.

Be sure the RF cables between the rig and the antenna are in good condition,
with no loose or intermittent connections, poor shield connections, or
corrosion.

I assume you installed the 1K resistor across RFC3 on the KPA100, and
checked that the HV bias is at least 110-150VDC or more. The higher the
better, to ensure good RF t-r switch isolation. This is mentioned on the
most recent KPA100 errata, which I have attached.


If the rig just changes the RF output level too much when the Power knob is
adjusted, do the mods shown at:

http://www.elecraft.com/Apps/Power_Control_Mod.html



--
73, Gary AB7MY
=========
gary@elecraft.com
Elecraft Technical Support


Kuva



niin ja mulla on tuo sivukansien maadoituspaikkojen hionta jänyt tekemättä... oon kai ohjeessa harpannu yli tai en oo huomannu ollenkaan.... siis paikkoja joihin PA:n maadoituskielet osuvat.

_________________
Elecraft K2 #5272


Ylös
 Profiili  
 
 Viestin otsikko:
ViestiLähetetty: La Huhti 15, 2006 7:58 pm 
Poissa

Liittynyt: Ke Tammi 25, 2006 10:59 am
Viestit: 210
Paikkakunta: Pieksämäki
Hieno juttu, että löysit ongelmaan ratkaisun. Garyllä on varmaan hyvät varastot erilaisiin ongelmatilanteisiin sopivia ohjeita.

Joo kyllä siellä ohjeissa on noiden sivulevyjen hionta mainittu. Onhan siellä palanen santapaperiakin mukana. Itse käytin dremeliä jollain sopivalla hiontakärjellä.

73 ja yritetään kuulostella huomenna. Olen QRV 4ab:n tontilta QRP K2:lla abt 13 SA. Pidetään hieman antennitalkoita ja meillä on K9AY-luuppi kimpparakennusrojektikin menossa.

Jukka, OH4MFA
K2 #4293


Ylös
 Profiili  
 
 Viestin otsikko:
ViestiLähetetty: Ma Touko 15, 2006 10:17 am 
Poissa
Avatar

Liittynyt: La Huhti 02, 2005 11:45 pm
Viestit: 97
Paikkakunta: Seinäjoki
postituslistalla oli näköjään muillakin samanlaisia ongelmia että teho ryntää..

tuolla oli ohje että siirretään yhtä kelaa kauemmaksi UHF liittimiestä:

http://www.n0ss.net/kpa100_40m_parasiti ... ention.pdf

_________________
Elecraft K2 #5272


Ylös
 Profiili  
 
 Viestin otsikko:
ViestiLähetetty: Ma Elo 14, 2006 3:31 pm 
Poissa
Avatar

Liittynyt: La Huhti 02, 2005 11:45 pm
Viestit: 97
Paikkakunta: Seinäjoki
Tein tuon yllä olevan modiksen... kerronpa sitten joskus onko ollut enää ongelmia.

Kuva

_________________
Elecraft K2 #5272


Ylös
 Profiili  
 
 Viestin otsikko:
ViestiLähetetty: Ti Elo 15, 2006 3:48 pm 
Poissa

Liittynyt: Ke Tammi 25, 2006 10:59 am
Viestit: 210
Paikkakunta: Pieksämäki
Terve!

Siihen oskillointiongelmaan on tulossa joku modiskin. Tom N0SS sitä tarjosi mulle field testiin, mutta kun ei se ollutkaan oskillointia mitä tuo mun KPA100 teki.

73 Jukka


Ylös
 Profiili  
 
 Viestin otsikko:
ViestiLähetetty: To Elo 17, 2006 5:27 pm 
Poissa
Avatar

Liittynyt: La Huhti 02, 2005 11:45 pm
Viestit: 97
Paikkakunta: Seinäjoki
Joo sain myös Juhalta (OH6OS) muutama viikko takaperin mailin, kun Tom oli kysellyt hänen oskillointi ongelmista.
Tuo tekemäni RFC10 paikan muutos ei vaikuttanut yhtään mitään.
Edelleen teho "karkailee" ssb:llä 7mhz:lla. Antaa 160w ulos ja ottaa 30A virtaa.

Lähetin Tompalle mailia ja mulle on nyt tulossa tuo Field Test paketti. Aika lailla muutoksia tulee.
Alla pdf ohje, mitä muutos pitää sisällään. On kuulemma jotain osanumeroa vailla valmis julkaistavaksi elecraftin sivulle.

http://www.oh6kw.net/stuff/docs/KPA100% ... 6-2006.pdf

_________________
Elecraft K2 #5272


Ylös
 Profiili  
 
 Viestin otsikko:
ViestiLähetetty: To Elo 17, 2006 9:12 pm 
Poissa

Liittynyt: Pe Huhti 14, 2006 10:01 am
Viestit: 9
Paikkakunta: Oulu
Onpa melkoinen korjaussarja. Liekö sitten yleinenkin vika tuo "oskillointi"? Minulla tuo oma K2 on edelleen ihan KAT2, KSB2-palikolla vaan varusteltu. Niin ja akkukin on.

En varmaan laitakaan sitä omaa PA:ta. Jos 100W on tarpeen joskus, niin sitten erillinen transistorimurskain tai kokonaan toinen radio.

Viime ajat on menneet antennispeksauksessa ja rakentelussa. Korvassani on jotain inhaa vahaa, ei kestä alle 600Hz ääniä kovinkaan hyvin. Ei voi workkia cw:tä. Alkaa tulla semmoista biittiä, "laulavaa cw:tä", tai joinakin päivinä kaikua, kuin tulis pitkää tietä kuulohavainnot päähän.

Rolf
oh6kxl

_________________
Rolf Moberg
oh6kxl
K2 #4759, KAT2, KSB2, KBT2


Ylös
 Profiili  
 
 Viestin otsikko:
ViestiLähetetty: Ti Syys 05, 2006 6:21 pm 
Poissa
Avatar

Liittynyt: La Huhti 02, 2005 11:45 pm
Viestit: 97
Paikkakunta: Seinäjoki
Nyt on asennettu nuo modikset kpa100:een.
Aikaa meni noin 2,5 tuntia.

Kerron myöhemmin auttoiko mitään.

_________________
Elecraft K2 #5272


Ylös
 Profiili  
 
 Viestin otsikko:
ViestiLähetetty: Pe Loka 27, 2006 11:28 am 
Poissa

Liittynyt: Ke Tammi 25, 2006 10:59 am
Viestit: 210
Paikkakunta: Pieksämäki
Onkos modiksesta ollut apua??

Jukka


Ylös
 Profiili  
 
 Viestin otsikko:
ViestiLähetetty: Ma Marras 06, 2006 7:38 pm 
Poissa
Avatar

Liittynyt: La Huhti 02, 2005 11:45 pm
Viestit: 97
Paikkakunta: Seinäjoki
En ole cw:llä tehon karkailua enää huomannut.
(Tosin edelleen 40m ssb:llä teho ryntää, mutta kun painaa ALC:n näytölle niin ei mitään ongelmia sen jälkeen)

Tuossa muutama kuva KPA100 piirilevystä modifioinnin jälkeen:
(levyltä puuttuu tosin nyt SWR-sillan diodit. (ovat tällähetkellä matkalla oh4mfa:lta mulle)

KuvaKuvaKuvaKuvaKuva
Kuvat aukeaa isoiksi kun niitä klikkaa.

_________________
Elecraft K2 #5272


Ylös
 Profiili  
 
Näytä viestit ajalta:  Järjestä  
Aloita uusi ketju Vastaa viestiin  [ 12 viestiä ] 

Kaikki ajat ovat UTC + 2 tuntia


Paikallaolijat

Käyttäjiä lukemassa tätä aluetta: Ei rekisteröityneitä käyttäjiä ja 2 vierailijaa


Et voi kirjoittaa uusia viestejä
Et voi vastata viestiketjuihin
Et voi muokata omia viestejäsi
Et voi poistaa omia viestejäsi
Et voi lähettää liitetiedostoja.

Etsi tätä:
Hyppää:  
cron
Powered by phpBB® Forum Software © phpBB Group
Käännös, Lurttinen, www.phpbbsuomi.com