Rakentelu Foorumi

Qrolle, Elecraft, Atmel, Pic, LC-Meter, OBD2, Robotit, yms yms
Tänään on To Maalis 28, 2024 10:59 pm

Kaikki ajat ovat UTC + 2 tuntia




Aloita uusi ketju Vastaa viestiin  [ 2 viestiä ] 
Kirjoittaja Viesti
 Viestin otsikko: Taajuuden kalibrointi
ViestiLähetetty: Ma Helmi 13, 2006 11:40 am 
Poissa
Avatar

Liittynyt: La Huhti 02, 2005 11:45 pm
Viestit: 97
Paikkakunta: Seinäjoki
The N6KR Method for setting the 4 MHz reference oscillator

(This is the unedited text from Wayne's original post to the Elecraft Reflector on 8/20/03)

All of the methods that have been described for calibrating the K2's 4-MHz oscillator will work. But I use a different technique that allows C22 on the Control board to be set to precisely the correct position, with no guesswork.

This method relies on the following simple observation. If you tune in an on-air signal at a known frequency, the difference between the *measured* VCO and BFO (using CAL FCTR) *must* equal that frequency, or C22 is not set correctly. (Actually, this holds for 160-17 m; on 15-10 m it's the sum, or VCO + BFO, that must equal the signal's frequency. But it's easier to do the adjustment of C22 on 17 m or lower because you don't have to do any math at all, as I'll explain below.)

Here's the procedure. It requires revision 2.XX firmware, and assumes you have already done Alignment and Test, Part II, at some point. The K2 should also be allowed to come up to room temperature.

1. Tune in a signal at a known frequency. Use one that's at an *exact* kHz boundary, so you can easily see when the VCO and BFO readings match in step 2. (I use WWV at 10, 15, or 20 MHz.) Use USB or LSB mode rather than CW, so that there will be no CW receive offset. In the case of a K2 I was calibrating, the VFO read 10000.17 when the signal was tuned in perfectly. If it had read 10000.00, no further improvement would have been possible.

TIP: Zero-beat the carrier precisely, or listen to a voice signal and adjust the VFO for the best quality. The more accurately you tune in the signal, the more accurately you'll be able to set C22, below.

2. Run CAL FCTR. Now alternately move the K2's internal counter probe between TP1 (VCO) and TP2 (BFO), adjusting C22 in small increments until the kHz and Hz digits at the two test points match as closely as possible. In my case, the two readings matched at 14913.60 and 4913.60. The difference is exactly 10000.00--the frequency of the on-air signal.

3. Put the counter probe on TP1 (VCO), switch to 40 meters, and run CAL PLL.

4. Put the probe on TP2 (BFO) and run CAL FIL. For each operating mode, vary each filter (or BFO) setting up 1 count, then back down, to force the K2 to take a new BFO measurement for each and store it in EEPROM.


The VFO dial should now be very well calibrated.

If we get a lot of positive feedback on this method, we'll post it as an application note.

73,
Wayne
N6KR

_________________
Elecraft K2 #5272


Ylös
 Profiili  
 
 Viestin otsikko:
ViestiLähetetty: Ke Kesä 07, 2006 5:23 am 
Poissa
Avatar

Liittynyt: La Huhti 02, 2005 11:45 pm
Viestit: 97
Paikkakunta: Seinäjoki
Tein eilen tuon taajuudenkalibroinnin tuon ylläolevan ohjeen mukaan, eli säätelin näyttämät samaksi TP1 ja TP2 mittapisteissä.

Nyt on taajuus joka bandilla tarkalleen kohdillaan. :D

Tuo taajuus on ollut mulla alusta asti pikkusen sivussa, kun säätelin elecraftin ohjeen mukaan,eli jollain bandilla on ollut hyvin lähellä oikeaa ja jollain bandilla pikkuisen sivussa, mutta nyt se on niinkuin pitääkin.

Filtterit säätelin vielä perään spectrogram ohjelmalla. Pikkuisen oli sivussa nekin, johtuen ehkä tuosta taajuuden säädöstä.

_________________
Elecraft K2 #5272


Ylös
 Profiili  
 
Näytä viestit ajalta:  Järjestä  
Aloita uusi ketju Vastaa viestiin  [ 2 viestiä ] 

Kaikki ajat ovat UTC + 2 tuntia


Paikallaolijat

Käyttäjiä lukemassa tätä aluetta: Ei rekisteröityneitä käyttäjiä ja 5 vierailijaa


Et voi kirjoittaa uusia viestejä
Et voi vastata viestiketjuihin
Et voi muokata omia viestejäsi
Et voi poistaa omia viestejäsi
Et voi lähettää liitetiedostoja.

Etsi tätä:
Hyppää:  
cron
Powered by phpBB® Forum Software © phpBB Group
Käännös, Lurttinen, www.phpbbsuomi.com