Rakentelu Foorumi

Qrolle, Elecraft, Atmel, Pic, LC-Meter, OBD2, Robotit, yms yms
Tänään on To Maalis 28, 2024 4:48 pm

Kaikki ajat ovat UTC + 2 tuntia




Aloita uusi ketju Vastaa viestiin  [ 4 viestiä ] 
Kirjoittaja Viesti
ViestiLähetetty: Su Syys 02, 2007 10:03 am 
Poissa
Avatar

Liittynyt: La Huhti 02, 2005 11:45 pm
Viestit: 97
Paikkakunta: Seinäjoki
Huomasin juuri että K2:n kaksi bandia on pimeänä.
muut bandit pelaavat mainosti, mutta nämä kaksi bandia on mykkänä.
Yhtään RF:ää ei lähde, mutta radio ottaa noin 20A virtaa.

Kokeilin ottaa valikosta PA:n pois käytöstä, mutta yhtään tehoa ei lähde ulos.

Onko ideoita mikä on hajalla?

_________________
Elecraft K2 #5272


Ylös
 Profiili  
 
ViestiLähetetty: Su Syys 02, 2007 10:45 am 
Poissa
Avatar

Liittynyt: La Huhti 02, 2005 11:45 pm
Viestit: 97
Paikkakunta: Seinäjoki
Irroitin PA:n ja nyt kun K2 on qrp versiona, niin nämä bandit toimivat, eli
vika on PA:ssa.

Purin PA:n mutta silmään siitä ei löydä mitään palanutta kohtaa tai huonoa juotosta mistään.

Pse help!

_________________
Elecraft K2 #5272


Ylös
 Profiili  
 
ViestiLähetetty: Ma Syys 03, 2007 10:55 pm 
Poissa
Site Admin
Avatar

Liittynyt: Su Huhti 03, 2005 6:10 pm
Viestit: 207
Paikkakunta: Kortesjärvi
Jaahas aikas jännä juttu. Mullahan savus silloin kerran jokin kuristin......ei jaksa muistaa. Pitäis kaivaa manuaali kytkis jotta kattelis. Voipi olla jokin sellanen ongelma. Eiköhän siihen apua saada 8)

_________________
73" DE OH6HGN Teemu
KP13MG / 635
QROlle s/n 65
K2 s/n 05109


Ylös
 Profiili  
 
ViestiLähetetty: Ti Syys 04, 2007 8:16 pm 
Poissa
Avatar

Liittynyt: La Huhti 02, 2005 11:45 pm
Viestit: 97
Paikkakunta: Seinäjoki
Kävin k2:n kanssa oh6mf:llä ja testattiin KPA100:n alipäästösuotimet
piirianalysaattorilla. No eipä siinä enää mitään vikaa ollut. Ruudulle tuli siistit alipäästösuotimen käppyrät.

Markun kanssa tultiin siihen tulokseen että jos vika uusii, niin ensin vaihdan alipäästösuotimen 20m/17m releet ja jos sekään ei auta, niin
sitten silvermica konkat jotka kuulemma saattavat oirehtia noin ollessan rikki, kun ne lämpenee.

Tuossa vielä vastaus Garylta ongelmaani.

Lainaa:
Gary Surrency to Jarno

Hi Jarno,

You might have a damaged relay in the lowpass filter if just 20m or 17m
does not work now. Use the RF probe in the kit (or an oscilloscope if
you can), to see if there is a loss of RF signal through the PA to
antenna signal path when on 17m or 20m. Also see if there is RF on the
lowpass filter toroids for any other band than 30/20m, when transmitting
on those bands. If so, a relay may be stuck or welded in the in-circuit
position, which will detune the PA stage greatly.

You can also check the VCO voltage and signal freq. at TP1 when on 17m
or 20m, to see if it is correct and if it falls within the limits shown
in the manual for the VCO voltage tests, and if the VCO frequency is
close to that shown in the VCO Table on the page just before the
schematics begin. The VCO freq. shown is with the VFO knob tuned to the
bottom end of each band.

Note that the KPA100 speaker should have a cupped metal magnetic shield
placed over its magnet, to prevent the magnet from affecting the VCO
relays in the K2. If not, order it from parts@elecraft.com.

Another possibility is there is a cold or missed solder connection
somewhere in the RF signal path. Inspect the PCB, the parts, and all
connections very closely for that, and try reheating all connections in
the suspect areas just as a precaution.

REMEMBER:

NEVER transmit with the heat sink of the K2 or the KPA100 removed, or
the PA transistors will be damaged. If there are any signs of heat on
the tabs or the PA transistors, or if the nylon shoulder washers are
melted, the PAs are probably damaged and will need to be replaced.


Always check the basic K2 without the KPA100 connected at all, and get
it working before reconnecting the KPA100. Don't just disable the KPA100
from the K2's menu - remove the KPA100 completely.

Use caution when soldering or repairing the kit, that none of the relays
are accidentally damaged with the soldering iron. Even a minor burn on
the relays can prevent them from working.


_________________
Elecraft K2 #5272


Ylös
 Profiili  
 
Näytä viestit ajalta:  Järjestä  
Aloita uusi ketju Vastaa viestiin  [ 4 viestiä ] 

Kaikki ajat ovat UTC + 2 tuntia


Paikallaolijat

Käyttäjiä lukemassa tätä aluetta: Ei rekisteröityneitä käyttäjiä ja 4 vierailijaa


Et voi kirjoittaa uusia viestejä
Et voi vastata viestiketjuihin
Et voi muokata omia viestejäsi
Et voi poistaa omia viestejäsi
Et voi lähettää liitetiedostoja.

Etsi tätä:
Hyppää:  
cron
Powered by phpBB® Forum Software © phpBB Group
Käännös, Lurttinen, www.phpbbsuomi.com